Midland XT30 Pro PMR Transceiver Pair in Green

Further details of Midland XT30 Pro PMR Transceiver Pair in Green

The Midland XT30 Pro is a bright green PMR two-way radio set containing two transceivers. The radios operate within the 446.00625-446.19375 MHz frequency range on 16 PMR446 channels. The units provide a communication range of up to 6 km in open, unobstructed environments with a direct line of sight.

Midland XT30 Pro PMR two-way radio set

The unit has a splashproof design resistant to humidity and dew. Its documented applications include keeping in contact during outdoor activities, excursions and weekend trips. For pair or group communication, the transceivers must be configured to the same channel and, where required, the same CTCSS tone.

XT30 Pro radio frequency characteristics

• Frequency range: 446.00625-446.19375 MHz
• Radio standard: PMR446
• Number of channels: 16
• Channel spacing: 12.5 kHz
• Transmit power: 500 mW ERP
• Modulation: FM
• Duty cycle: transmit 5%, receive 5%, standby 90%
• Category: B
• Spurious rejection: within ETSI regulations

The maximum range depends on terrain conditions and environmental obstructions.
In urban environments with buildings and other obstructions, the typical range is approximately 1-2 km. In open areas partially obstructed by trees, vegetation or houses, the range is approximately 2-4 km. In open and unobstructed environments with a direct line of sight, such as in mountainous areas, the range can reach 6 km.

Midland XT30 Pro communication functions

• Voice-activated VOX transmission without pressing the PTT button
• Single-level VOX setting
• 38 CTCSS tones
• Scan channel scanning
• Monitor function
• Call tone
• Switchable Roger Beep end-of-transmission tone
• Switchable keypad beep
• Keypad lock
• Adjustable volume
• Battery status indicator
• Automatic power-saving operation

CTCSS tones with code numbers from 1 to 38 can be assigned to the 16 channels. Radios communicating with each other must be set to the same channel and the same CTCSS tone. The selected channel and CTCSS tone are shown on the LCD.

VOX and Roger Beep functions

The VOX function activates transmission by voice without pressing the PTT button. When using an optional VOX headset, the headset switch must be placed in the VOX position. Roger Beep sends an audible signal to other users at the end of transmission and can be switched off.

Scan and Monitor functions

The Scan function monitors busy channels and stops on a channel where radio traffic is detected. The scanning direction can be selected with the control buttons. Scanning resumes approximately 5 seconds after activity on the busy channel stops.

The Monitor function enables the reception of weak signals. Stronger background noise may also be audible while this function is active.

XT30 Pro display and controls

• Alphanumeric LCD
• Selected channel indication
• Selected CTCSS tone indication
• Transmit and receive status indication
• VOX status indication
• Keypad lock indication
• Battery level indication
• PTT transmit button
• Menu setting button
• Mon/Scan function button
• Call and keypad lock button
• Volume, channel and function selection buttons

The keypad lock prevents accidental operation of the control buttons. When the keypad is locked, the PTT and Call buttons remain available. The Call function sends an audible signal to other radios operating on the same channel.

Midland XT30 Pro power supply and charging

• Power supply per radio: 3 x AAA rechargeable or alkaline batteries
• Capacity of supplied rechargeable batteries: 300 mAh
• Nominal alkaline battery supply voltage: 4.5 V
• Rechargeable battery supply voltage: 3.6 V, +/- 10% VDC
• Documented operating time: up to 5 hours with the supplied batteries
• Charging connector: micro USB
• Required USB power source charging current: at least 500 mA

The radio has an automatic current-saving circuit. If no signal is received for more than 10 seconds, the power-saving function is activated automatically. This can increase battery life by up to 50%.

A charging time of 10-12 hours is recommended before first use. Only rechargeable Ni-MH batteries may be installed in the unit during charging. Charging alkaline batteries or other non-rechargeable batteries is prohibited. Moving segments in the battery icon indicate charging, while steady segments indicate that charging is complete.

XT30 Pro connectors and accessory compatibility

• Two-pin Midland MIC/SPK accessory connector
• External microphone connector: 2.5 mm stereo
• External speaker connector: 3.5 mm mono
• Micro USB charging connector
• Connection for external microphones and headsets
• Compatible with two-pin Midland accessories

The VOX function can also be used with an optional headset equipped with a suitable selector switch. The headset must be switched to VOX for voice activation and to PTT for manual transmission control.

Midland XT30 Pro technical specifications

• Dimensions without antenna: 48 x 29 x 90 mm
• Weight without batteries: 83 g
• Operating temperature: -20 to +55 Celsius
• Receiver sensitivity at 12 dB SINAD: less than 0.30 uV
• Adjacent channel rejection: 70 dB
• Audio output power: approximately 250 mW at 10% THD
• Compliance: RED 2014/53/EU

XT30 Pro package contents

• 2 x Midland XT30 Pro PMR446 transceivers
• 2 x belt clips
• 6 x AAA Ni-MH rechargeable batteries, each with 300 mAh capacity
• 1 x two-way USB/micro USB charging cable

The two-way charging cable allows the two radios included in the set to be charged through a USB connection.

Safety and maintenance information

• The radio housing must not be opened and the unit must not be realigned
• A soft, clean cloth may be used for cleaning
• For heavy soiling, a cloth slightly dampened with water and neutral soap may be used
• Detergents, alcohol, solvents and abrasive materials must not be used
• Non-rechargeable batteries must not be charged
• The radio must not be charged without rechargeable batteries installed

In the event of a logical malfunction, abnormal display symbols or blocked functions, the radio can be restored to its factory settings. The reset procedure deletes all previously configured user settings.